 |
 |
 |
 |
HealthScreen-10 Urine Reagent Strips are comprised of 10 different reagent areas affixed to firm plastic strips. Packaged in a plastic bottle with a twist-off cap, each strip is stable and ready to use. Each strip is disposable. 100 per bottle, this product is clia-waived. Now only $19.97ea. bottle
Health Check 10 Panel Urine Test Strips by Express Diagnostics Clia Waived
Health Check 10 Panel Urine Test Strips by Drugcheck Clia Waived
- HealthScreen-10 Urine Check Procedure
1. Remove from the bottle only enough strips for immediate use and replace cap tightly. 2. Completely immerse reagent areas of the strip in fresh, well mixed urine. Remove the strip immediately to avoid dissolving out the reagent areas. 3. While removing, touch the side of the strip against the rim of the urine container to remove excess urine. Blot the lengthwise edge of the strip on an absorbent paper towel to further remove excess urine and avoid running over (contamination from adjacent reagent pads.) 4. Compare each reagent area to its corresponding color blocks on the color chart and read at the times specified. Proper read time is critical for optimal results. 5. Obtain results by direct color chart comparison.
 Note: All reagent areas except Leukocytes may be read between 1-2 minutes for screening positive urine from negative urine. Changes in color after 2 minutes are of no diagnostic value.
REAGENTS (Based on dried weight at time of impregnation) Glucose: 16.3%w/w glucose oxidase (Aspergillus niger, 1.3IU); 0.6%w/w peroxidase (horseradish, 3300 IU); 7.0% w/w potassium iodide; 76.1% w/w buffer and non-reactive ingredients. Bilirubin: 0.4% w/w 2,4-dichloroaniline diazonium salt, balanced with buffer and non-reactive ingredients. Ketone: 7.7% w/w sodium nitroprusside balanced with buffer and non-reactive ingredients. Specific Gravity: 2.8% w/w bromothymol blue, 69.0%; poly (methyl vinyl ether/maleic anhydride); 28.2% sodium hydroxide Blood: 6.6% w/w cumene hydroperoxide; 4.0% w/w 3, 3’, 5, 5’-tetramethylbenzidine; 89.4% w/w buffer and nonreactive ingredients. pH: 0.2% w/w methyl red; 2.8% w/w bromothymol blue; 97% w/w nonreactive ingredients. Protein: 0.3% w/w tetrabromophenol blue; 99.7% w/w buffer and nonreactive ingredients. Urobilinogen: 2.9% w/w p-diethylaminobenzaldehyde balanced with buffer and nonreactive ingredients. Nitrite: 1.4% w/w p-arsanilic acid, balanced with buffer and nonreactive ingredients. Leukocytes: 0.4% w/w indoxyl ester derivative; 0.2%w/w diazonium salt; 99.4% w/w buffer and nonreactive ingredients. Ascorbic Acid: 5.8% w/w ferric chloride; 4.9% w/w DTPA; 1.2% dipyridyl; 89.1% w/w buffer and nonreactive ingredients.
|
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
Features
- UrineCheck™ HealthScreen-10 urine reagent strips are firm plastic
strips to which several different reagent areas are affixed. Depending on the product being used, UrineCheck™ HealthScreen-10 urine reagent strips provide tests for Glucose, Bilirubin, Ketone (Acetoacetic acid), Specific Gravity, Blood, pH, Protein, Urobilinogen, Nitrite, Leukocytes, and Ascorbic Acid in Urine. Test results may provide information regarding the status of carbohydrate metabolism, kidney and liver function, acid-base balance, and bacteriuria.1,2 Please refer to the outside box and bottle label for the specific test parameters of the product you are using.
UrineCheck™ HealthScreen-10 urine reagent strips are packaged along with a drying agent in a plastic bottle with a twist-off cap. Each strip is stable and ready to use upon removal from the bottle. The entire reagent strip is disposable. Results are obtained by direct comparison of the test strip with the color blocks printed on the bottle label. No calculations or laboratory instruments are required.

|
|
 |
 |
 |
 |

|